Projector glossary

By the Home Projector Guide team · Updated · How we research

A projector spec sheet is full of abbreviations that decide whether a picture looks bright, sharp and sized right in your room. This glossary defines 55 of them in plain English, grouped by what they affect, with a real number wherever one helps. Each entry links to the guide that goes deeper, so you can look a term up, then check what it means for your own wall and seats. New to the word? See what a projector is.

Brightness and color

Lumens

A lumen measures the total visible light a projector sends out. More lumens gives a brighter picture on the same screen, but the same light spread over twice the area looks half as bright. For a dark room, plan on about 475 lumens landing on a 100 inch screen; with lamps on, plan on 1,500 to 2,100. The full sizing math is in how many lumens a projector needs.

ANSI lumens

ANSI lumens are lumens measured on the screen in a dark room as the average of nine readings, one in each box of a three-by-three grid, using the ANSI IT7.228 method. The number reflects the brightest white mode, so movie modes read lower. When you compare models, compare ANSI with ANSI. See the lumens guide and the brightest projectors.

ISO 21118 lumens

ISO lumens follow ISO/IEC 21118, which sets what a data projector's spec sheet must state and how to measure it. Anker says the conditions are stricter than ANSI, and gives one example: a projector rated 1,000 ANSI lumens might read about 850 ISO. No standard conversion exists, so never swap one for the other. More in the lumens guide.

LED lumens

"LED lumens" count the light the source makes before the lens and optics take their share, so they run well above ANSI. BenQ's rule of thumb, quoted by BGR, is to divide by about 2.4, and to divide an unlabeled "lumens" figure by about 16.7. CVIA lumens, a Chinese industry measure, have no independent conversion. Treat all three as warning signs. See how makers label brightness.

Foot-lambert

A foot-lambert (fL) measures how bright the picture looks on the screen. SMPTE's dark-room target is 16 fL, within an allowed range of 12 to 22, according to ProjectorCentral. A family room with lights on wants about 50 fL, and daytime viewing 60 or more. Formula: lumens times screen gain, divided by screen area in square feet. Worked tables are in the lumens guide.

Nits

A nit is one candela per square meter, the unit TVs use for brightness. One foot-lambert equals 3.426 nits, so the 16 fL dark-room target is about 55 nits and 50 fL is about 171. A TV rates hundreds or thousands of nits, which is why a projector in a lit room cannot match one. See projector vs TV.

Contrast ratio (native and dynamic)

Contrast ratio compares the brightest white a projector shows with its darkest black. Native contrast is measured with no help from dimming; dynamic contrast lets the iris or laser dim between scenes, so its figure is far bigger. Native numbers range from about 1,400 to 1,640:1 on one pixel-shifted DLP to 5,000:1 on the Valerion VisionMaster Max. Compare native with native. See Valerion's flagship.

ANSI contrast

ANSI contrast is measured on a checkerboard of 16 black and white squares shown at once, so stray light inside the projector and room counts. It reads much lower than native contrast and is a better guide to how a busy scene looks. Few makers publish it, so look for a reviewer's reading on our home theater picks.

Color brightness

Color brightness is the light output of the red, green and blue primaries, measured separately from white. A projector can be bright in white and dull in color. Epson rates the Home Cinema 2350 at 2,800 lumens in white under ISO 21118 and 2,800 in color under IDMS 15.4. See the 2350 page and DLP versus 3LCD.

Color gamut (Rec.709, DCI-P3, BT.2020)

Color gamut is the range of colors a projector can show, named by the standard it covers. Rec.709 is the HD baseline, DCI-P3 is the digital cinema range, about a quarter wider, and BT.2020 is the 4K and HDR target, roughly double the area of Rec.709. Few projectors cover BT.2020. Laser models reach furthest: see the laser projector guide.

HDR10

HDR10 is the base high dynamic range format: 10-bit color with one set of brightness data for the whole film. It is open, so nearly every 4K projector accepts it. A projector is far dimmer than the 1,000 nit masters, so it must squeeze the signal (see tone mapping). See HDR projectors.

HDR10+

HDR10+ adds scene-by-scene brightness data to HDR10, so the projector can adjust each scene instead of using one setting. It is royalty-free. The XGIMI Horizon 20 Max lists both HDR10+ and Dolby Vision. See HDR10+ and Dolby Vision projectors.

Dolby Vision

Dolby Vision is a licensed HDR format with dynamic data for every scene and up to 12-bit color. Projectors that support it are few, such as the Valerion VisionMaster Max and the XGIMI Horizon 20 Max. A stream must carry Dolby Vision for the projector to use it. See Dolby Vision projectors.

HLG

HLG (Hybrid Log-Gamma) is an HDR format made by the BBC and NHK for live broadcast. It carries no scene data, so it plays on screens that do not know HDR. A few projectors list it next to HDR10, such as the Optoma UHD38x family. See HDR projectors.

Tone mapping

Tone mapping is how a projector squeezes an HDR signal into the brightness it can actually produce. A film graded for 1,000 nits or more cannot be shown as is by a projector, so highlights get compressed. Dynamic tone mapping re-fits each frame; static uses one curve. See HDR projectors.

Picture and resolution

Native resolution (1080p, WXGA, 4K)

Native resolution is the number of real pixels in the imaging chip. 1080p is 1,920 x 1,080 (2,073,600 pixels); WXGA is 1,280 x 800; a 720p panel has 921,600. "1080p supported" only means the projector accepts a 1080p signal and scales it down to a lower-resolution panel. See what native resolution means and 1080p projectors.

4K (UHD)

Consumer 4K, also called UHD, is 3,840 x 2,160 pixels: 8,294,400, four times 1080p. The label describes the signal accepted, not always the pixels on the chip. A projector that "supports 4K" may show them with a 1080p chip. See 4K projectors.

Native 4K

A native 4K projector has a chip with about 8.3 million pixels. Sony's SXRD (3,840 x 2,160) and JVC's D-ILA NZ series (4,096 x 2,160) are native. Most others use pixel shifting. See native 4K compared with shifting.

Pixel shifting (XPR)

Pixel shifting moves the image a fraction of a pixel several times per frame, so a smaller chip builds a 4K picture. A 0.47 inch DLP chip holds 1,920 x 1,080 mirrors and shifts four times per frame to reach 8,294,400 pixels, according to Texas Instruments. TI calls its version XPR; Epson uses a glass plate. At 60 frames per second, that is 240 sub-images each second. See native 4K vs pixel shifting.

Aspect ratio (16:9, 2.35:1)

Aspect ratio is picture width divided by height. TV, streaming and games are 16:9 (1.78:1). Many movies are 2.35:1 or 2.39:1 and show black bars on a 16:9 screen. A 100 inch 16:9 picture is about 87 inches wide and 49 inches high. See cinema screen sizes.

Distance and placement

Throw distance

Throw distance is how far the lens sits from the screen. At a 1.0:1 throw ratio, a 100 inch 16:9 picture needs about 7.3 feet; at 2:1 it needs 14.5 feet. Measure from the point the maker uses, often the lens front. See how far a projector should be from the screen and the throw distance calculator.

Throw ratio

Throw ratio is throw distance divided by picture width. A 1.5:1 lens needs 1.5 feet of distance for each foot of picture width. For a 16:9 screen, width is the diagonal times 0.8716. A low ratio means a short distance. See throw ratio explained.

Short throw

Short throw usually means a ratio of 0.4 to 0.8:1, so a 100 inch picture sits about 3.6 to 5.8 feet from the screen. It suits shelves and small rooms. Makers draw the lines a little differently. See short throw projectors and 4K short throw models.

Ultra short throw (UST)

Ultra short throw is a ratio under 0.4:1. The lens sits inches from the wall, such as 1.2 feet for 100 inches at 0.16:1. UST projectors rest on a cabinet below the picture and replace a TV. See ultra short throw projectors and Hisense laser TVs.

Long throw

Long throw has no strict standard; it describes lenses with ratios of about 2:1 or higher, meant for the back of a room. At 2:1 a 100 inch picture needs 14.5 feet; at 3:1, 21.8. Most home projectors sit between 1.2 and 1.5:1. See throw ratio classes.

Keystone correction

Keystone correction squares up a trapezoid caused by projecting at an angle. Digital keystone shrinks the picture and can soften it, and BenQ says it adds about one frame of lag. Aim the projector straight and use lens shift where you can. See projector setup.

Lens shift

Lens shift moves the lens up, down or sideways inside the body without tilting the projector, so the picture stays square and sharp. Models list it as a percentage of picture height or width, for example plus or minus 10 percent vertical. Many small projectors have none. See setup tips and placing a projector on a wall.

Zoom

Optical zoom changes picture size from a fixed spot by moving lens elements, with no loss of sharpness. A 1.25x zoom changes a 1.20:1 lens to 1.50:1. Listed zooms range from 1.1x to 1.67x on home models. Digital zoom crops the image instead. See throw ratio explained.

Ceiling mount

A ceiling mount holds the projector upside down above the seats, and a menu setting flips the picture. It needs a lens that fits the room depth, a power outlet nearby and an HDMI run. See ceiling mounted projectors.

Light sources and chips

DMD

A DMD (Digital Micromirror Device) is the Texas Instruments chip inside DLP projectors. Each mirror is one pixel that tips on or off thousands of times per second. A 0.47 inch DMD holds 1,920 x 1,080 mirrors at 5.4 micron pitch, according to TI's DLP471TE datasheet. See DLP projectors.

DLP

DLP (Digital Light Processing) projects light off a DMD chip. Most home models use one chip and build color in sequence, which gives sharp edges and a compact body, and sometimes a rainbow effect. A DLP spec may count white light only. See DLP projectors and how a projector works.

3LCD

3LCD (an "LCD projector") splits light into red, green and blue and sends each through its own LCD panel. White and color light are equal, and rainbows do not occur, according to Epson. Blacks are usually lighter than on DLP. See LCD projectors and Epson projectors.

LCoS (SXRD, D-ILA)

LCoS is liquid crystal on silicon, a reflective chip. Sony calls it SXRD and JVC D-ILA. These chips can be native 4K and give the deepest contrast in home cinema. They are rare in small projectors. See native 4K and 4K home theater.

Rainbow effect

The rainbow effect is a brief red, green and blue flash some people see on bright edges or when moving their eyes, caused by single-chip DLP showing colors one after another. 3LCD models avoid it. No spec rates it, so use a store trial or a return window. See DLP projectors.

Laser phosphor

A laser phosphor projector fires blue lasers at a phosphor, which glows to make white light. It lasts about 20,000 to 30,000 hours and reaches full brightness at once. Most "laser projectors" are this type. See laser projectors.

RGB triple laser

An RGB laser uses separate red, green and blue lasers instead of a phosphor. It gives a wider color gamut and brighter colors; the JMGO N3 Ultimate and XGIMI Horizon 30 Pro use one. See the N3 Ultimate and laser projectors.

Speckle

Speckle is a shimmering grain that appears when laser light bounces off a screen. It is more visible with RGB lasers than phosphor and varies by screen. No spec rates it. See laser projectors.

LED light source

An LED projector uses red, green and blue LEDs instead of a lamp. It runs cool, starts instantly and lasts long: one four-LED engine is rated 20,000 to 30,000 hours. LEDs are usually dimmer than lasers of the same size. See LED projectors.

Lamp life

Lamp life is the number of hours until a lamp drops to about half its brightness. The Epson Home Cinema 2350's lamp is rated at 4,500 hours in normal mode and 7,500 in Eco. Lasers and LEDs outlast lamps many times over. A lamp warning light on the body usually points to a problem; see common projector problems. See the 2350.

Connections and sound

HDMI 2.1

HDMI 2.1 raises the link from 18 Gbps to 48 Gbps. That is what 4K at 120 Hz needs. Most projectors still use HDMI 2.0, and some have one 2.1 port and one 2.0. See gaming projectors and HDMI cables for projectors.

eARC

eARC (enhanced Audio Return Channel) lets a projector send audio back to a soundbar or receiver over HDMI. Per HDMI.org, it supports Dolby TrueHD, DTS-HD Master Audio and Atmos, up to 192 kHz and 24-bit. Both devices need an eARC port. See HDMI cables.

HDCP 2.2 and 2.3

HDCP is copy protection on HDMI. 4K streaming boxes and discs require version 2.2, and 2.3 came with newer devices. If any link is older, you may get a blank screen. See fixing no signal.

Miracast

Miracast mirrors a phone or PC to a screen over a direct Wi-Fi link, with no router. Support is common on Windows and Android and absent from iPhone. See phone to projector and projectors for Android.

Google Cast

Google Cast, or Chromecast built in, lets a phone send a video to the projector, which then plays it directly. It needs both on the same Wi-Fi. See Fire Stick and Chromecast setups.

AirPlay

AirPlay is Apple's way to send video from an iPhone, iPad or Mac. A projector needs AirPlay built in, or an Apple TV on the HDMI. See AirPlay projectors and iPhone projectors.

Screens

Screen gain

Screen gain is how much light a screen reflects toward the viewer compared with a matte white reference at 1.0. A 1.3 gain screen makes the picture about 30 percent brighter at the center. In the lumens formula, gain divides the lumens needed. See projector screens and screen vs white wall.

Half-gain angle

Half-gain angle is the viewing angle at which brightness falls to half its peak. High-gain screens have narrow angles, so seats at the sides see a dimmer picture. Find it on a screen's spec sheet. See home theater screens.

ALR (ambient light rejecting)

An ALR screen reflects projector light toward you and absorbs light from windows and lamps, so blacks look deeper in a lit room. A gray ALR screen does more than another 1,000 lumens. See ALR screens and daylight projectors.

CLR (ceiling light rejecting)

A CLR screen rejects light from above, such as ceiling lamps. It is built for ultra short throw projectors, which shine from below. See ALR and CLR screens.

Acoustically transparent

An acoustically transparent screen has tiny holes so sound passes through and speakers can sit behind it. The holes can cost a little brightness and may show a faint pattern. See home theater screens.

Gaming

Input lag

Input lag is the delay in milliseconds between a signal arriving and its light leaving the lens. Under about 20 ms at 60 Hz is good. ProjectorCentral measured 8 ms at 4K/60 on the XGIMI Horizon 20 Max. See gaming projectors and 4K gaming projectors.

ALLM

ALLM (Auto Low Latency Mode) tells a projector to switch to game mode when a console starts, then switch back. Some models only enter game mode when it is on. See gaming projectors.

VRR

VRR (variable refresh rate) lets the display follow the game's frame rate, which stops tearing. It helps when frame rates swing and is a part of HDMI 2.1. See gaming projectors and the Switch.

4K/120

4K/120 is a 3,840 x 2,160 signal at 120 frames per second. At 10-bit color it needs about 29.9 Gbps, more than HDMI 2.0 carries. PS5 and Xbox Series X can output it. See 4K gaming projectors.

Refresh rate

Refresh rate is how many times per second the picture updates, in hertz. Movies run at 24, TV at 60, games at 60, 120 or 240. At 120 Hz, a frame lasts 8.33 ms. A "3D ready" label means the projector accepts a 3D signal at a higher refresh rate; see 3D projectors. See gaming projectors.

Sources